Instruction manuals

GDC31-Installation Manual (RevM12!4!07)

Published
of 77
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Related Documents
Share
Description
gdc
Transcript
   Equipment Installation Manual, EQUIPMENT INSTALLATION MANUAL For the GDC31 ROLL STEERING CONVERTER P/N 1049-4000-XX-001( ) REV M December 4, 2007 DAC International 6702 McNeil Drive Austin, TX 78729 © Copyright 2007, DAC International. All rights reserved. 1049-2510-01 M.doc 1049-2510-01 Rev M Page 1 of 77    Equipment Installation Manual, RECORD OF REVISIONS REV   DESCRIPTION DATE APPROVED IR INITIAL RELEASE E266 4-5-04 LW A Correct P/N of mating connector E269 4/8/04 LW B CHANGED BREAKER TO 2 AMPS E272-04 4/19/04 LW C Reduced 28V and 14V install kits into one universal kit and added instructions for configuration. Added wiring diagram for Bonanza A-36. E306 7/26/04 LW D Omit approval pending E321 9/17/04 LW E Add numerous wiring diagrams E327 10/22/04 LW F Add additional wiring diagrams, correct table 4 E389 3/30/05 LW G Add lighting bus circuit diagram to all wiring diagrams. Omit jumper on drawings Fig. 9 & 11. Add note to installation section, page 16. E415 5/20/05 CC H Add Reference page for lighting connections and correct drawings. Add KLN-94 incompatibility stmt to Operation Overview and Appendix A. Correct pin references on ARINC HSI drawings. Remove Isolation Coupler from Fig. 10. Add –03 model & update all applicable sections and drawings. Add Isolation Coupler to Figure 4 drawing. Add Follow-on Installation Data form and instructions. E432 10/5/05 LW I Add FD112 and AP107 drawing. E461 Delete 1049-4200-10 kit information. Edit drawings to reflect –03 vs –01 differences 11/16/05 CC J Correct typo on Figure 3 ARINC HSI with Century IV drawing; Add Isolation Coupler requirement statement to “OPTIONAL EQUIPMENT” section; 2/21/06 LW K Add various drawings; minor changes on misc drawings; added Appendix D, GPS Receiver interconnect to RS232/ARINC 429; Added STC Permission Stmt E645 12/12/06 LW 1049-2510-01 M.doc 1049-2510-01 Rev M Page 2 of 77    Equipment Installation Manual, REV   DESCRIPTION DATE APPROVED L Added various drawings; Added gain jumper flag note to various King autopilot drawings; Corrected  pin-out on various STEC drawings; Add note to Appendix C. Add Note: “This A/P is not STC’d” on all relevant drwgs. Fig 2 – Add Note: Fig 4 – Remove AP-Offset line  – Add jumper b/t pin 10 & 11 – GainSel 1  – Add pin 16 to J2 – 400hz Rtn Fig 8 – Add lines b/t DG and Iso Coupler and pin info for 52D54 Exc Fig 19 – Change jumper for GainSel2 to dotted line and add flag note: “If turn is sluggish, install this jumper”. Fig 20 – Add line between pin 13 of AP Comp and  pin 15 of GDC31  – Add KCP 299 pins and dotted lines Fig 26 – Add Iso Coupler to prevent voltage spike to Roll Computer when setting breaker. Fig 28 – Add STEC 30 Pinout E729 6/8/07 LW M Added various drawings; Revised website link on  pg 26; Added KLN-89A to Operation Note Appendix A Note as non-compatible with the GDC31. Fig 7 - Revised wiring illustrations Fig 13 - Add 5kz flag note Fig 20 - Remove Type Sel jumper & added jumper to Phase Sel Fig 31 - Add Type Sel jumper Fig 32 – Add Phase Sel 12/06/07 LW 1049-2510-01 M.doc 1049-2510-01 Rev M Page 3 of 77    Equipment Installation Manual, Table Of Contents RECORD OF REVISIONS...........................................................................................................................2 INTRODUCTION:........................................................................................................................................7 DESCRIPTION:.............................................................................................................................................7 PART NUMBERS:........................................................................................................................................8 REGULATORY COMPLIANCE:................................................................................................................8 Software.....................................................................................................................................................8 PMA...........................................................................................................................................................8 Environmental............................................................................................................................................8 SUPPLIED EQUIPMENT.............................................................................................................................9 OPTIONAL EQUIPMENT..........................................................................................................................10 SPECIFICATIONS:.....................................................................................................................................11 Physical:...................................................................................................................................................11 Electrical:.................................................................................................................................................11 Serial Data Input:.....................................................................................................................................11 ARINC 429 Input: (-03 Only).................................................................................................................12 Roll Sum Steering Output:.......................................................................................................................12 ARINC 429 Output: (-01 Only)..............................................................................................................12 Reference Inputs:.....................................................................................................................................12 AP Offset Input:.......................................................................................................................................13 Annunciator Output:................................................................................................................................13 Flag Input:................................................................................................................................................13 Certification:............................................................................................................................................13 Reliability:................................................................................................................................................13 OPERATION:..............................................................................................................................................14 Overview..................................................................................................................................................14 Analog Output..........................................................................................................................................14 Reference Inputs (Excitation).................................................................................................................14 ARINC 429 Output..................................................................................................................................14 ARINC 429 Input.....................................................................................................................................15 GPS Mode Annunciator Control..............................................................................................................15 Super Flag Input.......................................................................................................................................15 INSTALLATION.........................................................................................................................................16 Material Not Supplied..............................................................................................................................16 Special Tools............................................................................................................................................16 Mounting Considerations.........................................................................................................................17 Wiring Considerations.............................................................................................................................17 Steering Output Scale Factor Determination...........................................................................................18 Configuration Pins...................................................................................................................................19 Gain Settings Using Ref 1 input J1-18.....................................................................................................19 Gain Settings Using Ref 2 input J1-6.......................................................................................................19 Phase Selection........................................................................................................................................20 1049-2510-01 M.doc 1049-2510-01 Rev M Page 4 of 77 
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks