Thread Estimation Mens 5pkt Jean

of 12
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Related Documents
Thread Calculator as published on internet
  New!  ANE CALC   Help Guide    ANE CALC is a tool developed by American & Efird (A&E) to assist in estimating the amount of thread consumed  in a sewn product. This information can then be used to calculate the Thread Cost per Garment and the estimated number of cones  you will need for a quantity of sewn products you are planning on producing. You do not need to have any special software on your computer because  ANE CALC was developed using Microsoft ®  Excel ®  spreadsheets. The  ANE CALC workbook has Sheets shown as Tabs at the bottom used for the following: INSTRUCTIONS  tab on how to use the program. New! ISO STITCHES for identifying the correct stitch type. New! WORKSHEET  tab and THREAD COST Tabs have been combined so you can see everything on one spreadsheet. This also allows you to copy the entire worksheet to compare thread cost using other thread combinations. mm to Inches  tab that helps you convert fractions of an inch to millimeters. STARTING A NEW  ANE CALC   SPREAD SHEET - To begin a new  ANE CALC spreadsheet, you can either use an existing Apparel Guidelines  ANE CALC   spreadsheet for a similar garment and modify it for the garment you are doing the analysis on; or you can decide to begin from scratch with a new Spreadsheet. WHEN STARTING FROM SCRATCH - When you are starting from scratch with a new Spreadsheet, iIt is important that you select the correct spreadsheet for the weight of the fabric being used in the garment. There are three basic  ANE CALC   spreadsheets: Light Weight 2 to 4 oz weight fabrics Medium Weight 5  –  8 oz weight fabrics Heavy Weight 9  –  15 oz weight fabrics The Weight of fabric determines the ratio of Needle to Bottom hread on the Thread Consumption Table that is used to estimate he amount of thread consumed. - For each sewing operation on the garment, list the name of the sewing operation, what ISO Stitch Type is being used, how many rows of ISO Stitch there are, the Stitches Per Inch (SPI), and the length of the seam. AVERAGE SEAM THICKNESS - At the top of each  ANE CALC spreadsheet is a cell for the average thickness of the seam in millimeters. This is based on SELECTING THE ISO STITCH TYPE -   If you are not family with the ISO 4915 stitch numbers, you can look them up on the ISO4915 Tab below. -   For many stitches you must first measure the needle spacing or seam width before selection the stitch. (Ex. 504 - 1/8”    –  3 Thd Overedge). -   It is important to select the correct ISO 4915 stitch because this will determine the amount of thread consumed in making the seam. NUMBER OF ROWS OF STITCH -   Refers to the number of rows of ISO stitch used to make the seam. This does NOT refer to the number of needles or the number of pieces (i.e., pockets, etc.) being sewn, BUT the number of rows of the ISO stitch you selected in the previous column to make the seam. -   For example, a 406 stitch is a two needle bottom coverstitch. This two needle stitch type makes only one row of stitch. Rule: whenever the needles are connected with thread on either the top or bottom side of the seam, one row of stitch is being produced. -   On the other hand, when you twin needle topstitch a pocket with a 301 Lockstitch, then two independent rows of lockstitch are being used. SPI -   SPI refers to Stitches Per Inch and is the measurement of the number of links of thread between needle holes in one inch. -   For example, a typical number of stitches per inch on denim would be 8 s pi. See A&E’s technical bulletin on Selecting the Proper Stitches Per Inch can be found on A&E’s website.   LENGTH OF SEAM -   The length of seam is the measurement of the seam length including seam margins but does not include chain-off. -    A&E has  ANE CALC   spreadsheets available in either inches & yards or centimeters & metres. The selection of the proper sheet is normally dependent upon the international location and what measurement system is used for the cone put-ups. To convert from meters to yards multiply times .91. To convert from meters to yards divide by .91. -   In the Americas., a typical cone of thread is wound on a 6,000 yard put-up. In Europe or Asia, a typical cone is wound on a 5,000 metre put-up. Many sewing operations have mirror components on each side of the garment. A right and left cuff, a right and left pocket, etc.  ANE  CALC   Instructions (continued)   the average seam thickness in the entire garment. In most cases, you will not have to change this if you are using the correct spreadsheet for Light, Medium or Heavy weight fabric. -   If the sewing operation includes sewing both of these parts, then double the measurement for the seam length. BARTACK, BS, BH & EMBROIDERY -   If a bartack, buttonsew, buttonhole or embroidery selection is made from the ISO Stitch Column, you should always enter the number o f tacks, buttons, etc. under Rows of Stitch, and “1” under SPI and “1” under length of seam. (ex. Tack Belt Loops –  10 tacks, 1 under SPI and 1 under Length of Seam). HIDING ROWS -    A typical  ANE CALC   spreadsheet has enough rows for 50 operations but in many cases, you will not need all these rows. -   If you want to Hide the Rows between the last operation and the Totals at the bottom of the spreadsheet, Click in the left hand margin and drag down the Row numbers until you are just above the Totals. - Next right click your mouse and select HIDE. INSERTING A NEW ROW - First, click in the row where you want to insert the new row. -   Next, right click and select  Copy. -   Now right click again and select  Insert Copied Cells. -   You will now have two identical rows of one above the other. -   Next, right click on the Stitch Box in the new row you just added. -   Then select Format Control from the pop-up menu. -   Change the Cell Link to the proper Row Number. In this case, change the D17 to D16 and then click on OK.  ANE  CALC   Instructions (continued)  -   Now you can change the operation numbers and the information in the New Row you just inserted. -   If you change the Stitch Type, make sure that you put the right thread type under Needle, and either Bobbin or Looper. New!    INSERTING THREAD SIZE, TYPE & COLOR -   New! To make  ANE CALC   easier, we have added a section at the top of the spreadsheet for putting the thread size / type descriptions (column M). You can also change the Thread Group Description rather than using Thread type #1, #2, etc. (i.e., Topstitching #1, Looper threads, Serging threads) -   New! When you enter a thread Tex Size/Type/Clr (i.e, T-24 Perma Core - Clrs), you will see this same thread identification to the right in column O. This can then be copied and pasted in all operations using this particular SKU. -   For  ANE CALC   to be able to calculate the cost per garment, the Thread information for each operation must be inserted next to the thread consumption calculation. -   Rule: There must be a thread description placed in the appropriate column for the Needle, Bobbin and Looper thread positions where there is any thread consumed. IF AT THE BOTTOM OF THE SPREADSHEET UNDER TOTAL YARDS YOU SEE THE SAME NUMBER REPEATED, YOU MISSED  AN CELL FOR THREAD SIZE & TYPE. -   We strongly recommend that you copy and paste all thread descriptions as mentioned above. Never type the same thread Size / Type multiple cells at the top as  ANECALC will double the consumption. CALCULATING TOTAL THREAD CONSUMPTION BY SKU -   Rule: The total amount of thread under the SKU Summary must be equal to the Total amount of thread found under the worksheet. If they are not the same, then you have missed copying and pasting an SKU in the SKU Summary portion of the spreadsheet. CALCULATING THREAD COST PER GARMENT -   To calculate the thread cost per garment, enter the thread put-up and price per cone. Example: 6,000 @ $6.00. -    Any currency can be used on  ANE CALC.   CALCULATING NUMBER OF CONES NEEDED - To calculate the Number of cones required, type in the production requirement and  ANE CALC   will calculate the number of cones needed for the thread in the sewn products. - If very small lots of production are to be produced, then more thread may have to be ordered to have the proper coverage on there are coverage issues because there are too many variables that can affect this calculation. -    Ask about  ANE CALC PLUS  that can help calculate the total cones required to thread up a sewing production line. -   New!    If you have any questions, contact your local A&E Technical Support Representative.   the sewing floor. By coverage, we mean the minimum number of cones needed to thread up the machines on a production line to run the work efficiently without delay.  ANE CALC   will not calculate the minimum amount of cones you will need when

Englishpdf Cm

Jul 23, 2017

2 ltd cases

Jul 23, 2017
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks